Kitchen Worktops, Integrated Sinks & Faucets · 2026 Specification

Stainless Steel Kitchen Countertops, Integrated Sinks & Faucets

Specify your working surface with full material transparency: nominal versus measured sheet thickness across 304 stainless steel, QN1803, solid stainless plate, 20 mm quartz, and 12 mm sintered stone — paired with 41 active edge profiles, 52 kitchen sinks, and 36 faucets backed by accredited GQI emission tests.

41 Edge Profiles

24 stainless · 12 quartz (20 mm) · 5 sintered stone (12 mm)

52 Kitchen Sinks

Handmade, pressed, workstation & Fadior drainer channels

36 Faucets

22 imported partner & 14 standard models, body alloy disclosed

< 0.005 mg/m³

Formaldehyde not detected on 304 & QN1803 countertops (GQI)

Book Kitchen Consultation

Verified against Fadior 2026 countertop thickness notice (2026-09-04), current active product codes, and GQI lab reports SQ2505791 & SQ2505792.

Brushed 304 stainless steel kitchen countertop with a flush welded-in workstation sink, perforated stainless drainer plate, and pull-out kitchen faucet
Welded-In 304 Sink & Worktop
Real Fadior installation: 304 stainless steel workstation sink welded directly into a brushed stainless kitchen countertop.

01 · Countertop Substrates & Measured Thickness

Honest countertop thickness: nominal specification versus measured sheet.

Every stainless steel countertop is ordered by nominal sheet gauge, while finished thickness sits within the negative tolerance permitted by GB/T 4237-2015 and GB/T 709-2019 after grinding, embossing, and levelling. Compare all six countertop substrate families side by side before choosing your edge profile.

Active Fadior countertop substrates — nominal vs measured thickness (mm), tolerance, grain direction, and scratch-resistance
Countertop SurfaceAlloy / MaterialNominalMeasuredToleranceGrain DirectionScratch-Resistant
304 Brushed (Random-Grain)
304 Stainless1.5 mm1.3 mm±0.1 mmNon-directionalNo
304 Snow-Crystal Steel
304 Stainless1.5 mm1.3 mm±0.1 mmNon-directionalYes
304 Rock-Grain Steel
304 Stainless1.5 mm1.3 mm±0.1 mmDirectionalYes
304 Etched-Lustre & Cloud-Fleck
304 Stainless1.5 mm1.3 mm±0.1 mmNon-directionalYes
304 Titanium Steel Finish
304 Stainless1.2 mm1.05 mm±0.1 mmNon-directionalYes
Q1803 Stainless Countertop

1.0 mm outer + 0.4 mm honeycomb + PVC crust core + steel square tube

QN1803 (Not 304)1.0 mm0.9 mm±0.1 mmNon-directionalNo
Solid Stainless Plate (Random, Snow, Titanium, Carbon)

Random/Snow 5·6·8·10 mm (actual 4.75–9.75 mm); Titanium 5·8 mm only (actual 4.75 / 7.75 mm); Carbon-tone 5·6·8·10 mm (actual 4.6–9.6 mm)

304 Stainless5 · 6 · 8 · 10 mm4.6–9.75 mm±0.3 mmNon-directionalYes
Quartz Kitchen Countertops

12 active 20 mm edge profiles with 50–60 mm aprons

Engineered Quartz20 mm20 mm slabPer slab sheetSlab-dependentPer stone spec
Sintered Stone Countertops

5 active 12 mm edge profiles (50 mm mitred apron and 12 mm slim island edges)

Sintered Stone12 mm12 mm slabPer slab sheetSlab-dependentPer stone spec

Material Boundary Notice — QN1803 Is Never Described as 304

The Q1803 countertop system uses austenitic-class QN1803 stainless sheet (1.0 mm nominal / 0.9 mm measured) over a 0.4 mm QN1803 honeycomb layer, rigid PVC crust board, and steel square tube (depth 300–980 mm, length 200–4,000 mm). It is independently emission-tested (GQI SQ2505792, formaldehyde not detected) and is always itemized transparently as QN1803 — never substituted for or labeled as 304 stainless steel.

Measurement standard (2026-09-04): measure stainless sheet thickness with a micrometer at least 100 mm inward from the sheet edge; edges run 0.04–0.1 mm thinner than center after grinding, embossing, and levelling.

02 · Active Edge Profiles & Matching Finishes

24 stainless steel edge profiles, 12 quartz profiles, and 5 sintered stone profiles.

Front apron geometry and rear wall upstand are engineered and ordered together as a single verified specification code. Every profile below is currently active in production; discontinued early bevel profiles are excluded.

Choose between clean straight no-lip edges for minimalist islands, Bevel Water-Stop No. 2 raised fronts for wet cooking zones, ultra-slim 8.5–13.5 mm composite profiles, or solid 5–10 mm stainless plates.

SectionOrder CodeSheet / SlabFront ApronRear Upstand
FBBAA002NAA011.0 mmStraight, no lip100 mmNo upstand
FBBAA005GBG011.0 mmBevel water-stop No. 252.5 mmIntegral square50 mm
FBBAA005GCG011.0 mmBevel water-stop No. 252.5 mmSeparate square50 mm
FBBAB002FAA021.5 mmStraight, no lip50 mmNo upstand
FBBAB002FBG011.5 mmStraight, no lip50 mmIntegral square50 mm
FBBAB002FCG011.5 mmStraight, no lip50 mmSeparate square50 mm
FBBAB002FEG011.5 mmStraight, no lip50 mmIntegral coved base50 mm
FBBAB002KAA021.5 mmStraight, no lip120 mmNo upstand
FBBAB002KBG011.5 mmStraight, no lip120 mmIntegral square50 mm
FBBAB002KEG011.5 mmStraight, no lip120 mmIntegral coved base330 mm
FBBAB002TCG011.5 mmStraight, no lip13.5 mmSeparate square50 mm
FBBAB002TEG011.5 mmStraight, no lip13.5 mmIntegral coved base50 mm
FBBAB005GBG011.5 mmBevel water-stop No. 252.5 mmIntegral square330 mm
FBBAB005GEG011.5 mmBevel water-stop No. 252.5 mmIntegral coved base330 mm
FBBAB005LEG011.5 mmBevel water-stop No. 2122.5 mmIntegral coved base120 mm
FBBAB005QEG011.5 mmBevel water-stop No. 277.5 mmIntegral coved base120 mm
FBBAB005RDF011.5 mmBevel water-stop No. 270.5 mmIntegral rounded top & coved base100 mm
FBBAB005REG011.5 mmBevel water-stop No. 270.5 mmIntegral coved base120 mm
FBBAC002ACG016 mmStraight, no lip6 mmSeparate square50 mm
FBBAD002CAA0110 mmStraight, no lip10 mmNo upstand
FBBAL002SBG011.5 mmStraight, no lip8.5 mmIntegral square50 mm
FBBAM002UAA015 mmStraight, no lip5 mmNo upstand
FBBAM002UCG015 mmStraight, no lip5 mmSeparate square50 mm
FFBBAL002SEG011.5 mmStraight, no lip8.5 mmIntegral coved base50 mm

Matching Door & Panel Finishes — Raw Stainless Steel (Reference)

Reference swatches from Fadior's kitchen door and panel finish palette shown for visual coordination alongside your countertop; physical countertop and panel samples govern final approval.

Long-Grain Brushed Steel
Long-Grain Brushed Steel
FDADZZZ006
Raindrop Embossed
Raindrop Embossed
FDADZZZ008
Natural Cross Hairline
Natural Cross Hairline
FDADZZZ013
Anti-Fingerprint Snowflake Satin
Anti-Fingerprint Snowflake Satin
FDADZZZ058
Carbon Gold Steel
Carbon Gold Steel
FDADZZZ068
Cloud Wisp Texture
Cloud Wisp Texture
FDADZZZ069

03 · Real Kitchen Sinks & Faucets Catalog

Filter 52 active kitchen sinks and 36 faucets by style, build, and body material.

Browse every active sink bowl, multifunction workstation, Fadior in-house drainer channel, and partner kitchen or basin faucet. Filter by construction type or search directly by order code.

Strict Material Transparency — Sinks & Faucets Confirmed Per Model

Sink bowls vary by model across brushed 304 stainless steel, 304 snow-crystal, 304 micro-embossed, 304 rock-grain, and quartz composite (FAG03029), while kitchen and basin faucets are sourced partner fittings whose body materials span chrome-plated brass/copper, matte-black brass/copper, brushed 304 stainless steel (FAG08002), stainless steel, and zinc alloy (FAG08054). Exact alloy grade and documentation are always confirmed per selected model on your project quotation — never assumed to be uniformly 304.

Showing 12 of 52 active models

Square Double-Bowl Handmade Sink (FAG03002)
FAG03002Brushed 304 stainless

Square Double-Bowl Handmade Sink

  • Double bowl
  • Handmade folded
Square Double-Bowl Pressed Sink (FAG03003)
FAG03003Brushed 304 stainless

Square Double-Bowl Pressed Sink

  • Double bowl
  • Deep-drawn pressed
Square Double-Bowl Pressed Sink (FAG03004)
FAG03004Brushed 304 stainless

Square Double-Bowl Pressed Sink

  • Double bowl
  • Deep-drawn pressed
Double-Bowl Workstation Sink with Knife Slot & Cup Rinser (FAG03005)
FAG03005Brushed 304 stainless

Double-Bowl Workstation Sink with Knife Slot & Cup Rinser

  • Knife holder
  • Cup rinser
  • Double bowl
Double-Bowl Pressed Sink with Knife Holder (FAG03006)
FAG03006Brushed 304 stainless

Double-Bowl Pressed Sink with Knife Holder

  • Knife holder
  • Double bowl
Single-Bowl Pressed Sink with Rounded Corners (FAG03007)
FAG03007Brushed 304 stainless

Single-Bowl Pressed Sink with Rounded Corners

  • Single bowl
  • Rounded corners
Round Pressed Stainless Sink (FAG03008)
FAG03008Brushed 304 stainless

Round Pressed Stainless Sink

  • Round basin
  • Deep-drawn pressed
Square Double-Bowl Handmade Sink (FAG03009)
FAG03009Brushed 304 stainless

Square Double-Bowl Handmade Sink

  • Double bowl
  • Handmade folded
Single-Bowl Pressed Sink with Knife Holder (FAG03010)
FAG03010Brushed 304 stainless

Single-Bowl Pressed Sink with Knife Holder

  • Single bowl
  • Knife holder
Single-Bowl Handmade Sink with Right Drainboard Slope (FAG03013)
FAG03013Brushed 304 stainless

Single-Bowl Handmade Sink with Right Drainboard Slope

  • Single bowl
  • Right slope drainboard
Single-Bowl Handmade Sink with Left Drainboard Slope (FAG03014)
FAG03014Brushed 304 stainless

Single-Bowl Handmade Sink with Left Drainboard Slope

  • Single bowl
  • Left slope drainboard
Square Single-Bowl Handmade Sink (FAG03018)
FAG03018Brushed 304 stainless

Square Single-Bowl Handmade Sink

  • Single bowl
  • Handmade folded

11 Active Sink Workstation Racks & Plumbing Fittings

Pair Fadior snow-crystal drainer channels with 8 mm solid snow-crystal workstation racks (9 active racks) plus supply hoses and basin drain fittings.

FAG20177
Large drainer rack
8 mm solid snow-crystal steel
FAG20178
Small drainer rack
8 mm solid snow-crystal steel
FAG20179
Large dish rack
8 mm solid snow-crystal steel
FAG20180
Small dish rack
8 mm solid snow-crystal steel
FAG20181
Twin utensil holder
8 mm solid snow-crystal steel
FAG20182
Single utensil holder
8 mm solid snow-crystal steel
FAG20183
Chopping-board rack
8 mm solid snow-crystal steel
FAG20184
Knife rack
8 mm solid snow-crystal steel
FAG20185
Lift-up socket frame
8 mm solid snow-crystal steel
FAG08040
Faucet supply hoses
Braided supply accessory
FAG03114
Basin pop-up drain
PP body with plated steel cover (not 304)

04 · Countertop Joinery, Welded Sinks & Work-Zone Planning

How tight-seam corners, welded bowls, and edge profiles are built to last.

Unlike wood-core laminates or porous stone seams, Fadior stainless steel countertops are engineered with bolted tight-seam L-joints, inspected flush sink welds, and ergonomic horizontal prep clearances.

TIGHT-SEAM CORNER JOINT & QN1803 LAYERED SECTION

SCHEMATIC · N.T.S.
A · TIGHT-SEAM L-CORNER JOINTHairline straight butt jointUnderside steel L-plateM6 × 10 boltsB · Q1803 COUNTERTOP BUILD-UPGRADE QN1803 · NOT 3041.0 mm QN1803 skin0.4 mm honeycombPVC crust coreSteel square tube

01 · Tight-Seam L-Joint Method

  • — Fold radius eliminated along the meeting line for a flat, crisp hairline seam.
  • — Locked from underneath with steel L-plates and M6 × 10 machine screws.
  • — Shimmed flush on levelled base cabinets before load-checking every joint.

02 · Q1803 Multi-Layer Section (Not 304)

  • — Nominal 1.0 mm (actual 0.9 mm) QN1803 outer sheet over 0.4 mm honeycomb.
  • — Supported by a rigid PVC crust board and structural steel square tube.
  • — Specified D 300–980 mm × W 200–4,000 mm; front lip 2.3 mm, rear R10 upstand 50 mm.
Schematic showing Fadior's tight-seam corner joint (a fine straight seam remains visible) alongside the four-layer Q1803 stainless countertop structure (grade QN1803 — never described as 304).Corner Joint & Core · mm

INTEGRATED WELDED-IN SINK CUTOUT & DRAINAGE SLOPE

SECTION · N.T.S.
Worktop Depth ≥ 600 mm (Large Sinks)304 Stainless WorktopFlush Welded RimBasin Drainage SlopeDrain Outlet

Factory Welded-Sink Acceptance Rules

  • — Zero burn-through at the worktop-to-bowl weld seam.
  • — Zero solder or weld spatter inside the stainless bowl.
  • — Non-blackened seam edge polished smooth and burr-free.
  • — Under-sink cabinets support U-shaped plumbing cutout drawers.
Schematic section of a 304 stainless steel kitchen sink welded directly into a stainless steel countertop for hygienic wipe-in cleaning without exposed silicone lip buildup.Integrated Sink · mm

COUNTERTOP EDGE GEOMETRY · WATER-STOP VS STRAIGHT VS SOLID PLATE

PROFILES · N.T.S.
01 · BEVEL WATER-STOP NO. 202 · STRAIGHT NO-LIP EDGE5 · 6 · 8 · 10 mm03 · SOLID STAINLESS PLATE

01 · BEVEL WATER-STOP NO. 2

Raised front lip + coved rear upstand

Front apron 52.5 / 70.5 / 77.5 / 122.5 mm; rear upstand 50–330 mm (integral coved or square).

02 · STRAIGHT NO-LIP EDGE

Clean flat perimeter for islands & linear runs

Front apron 8.5 / 13.5 / 50 / 100 / 120 mm; pairs with 0 mm (island) or 50–330 mm upstand.

03 · SOLID STAINLESS PLATE

5 · 6 · 8 · 10 mm architectural slim edge

Machined solid 304 plate edge with zero hollow fold; available flush or with 50 mm separate upstand.

Comparison of Fadior's three active stainless steel front-edge geometries. Bevel water-stop No. 2 is the current raised bevelled front profile.Edge Cross-Sections · mm
Close-up photograph of a brushed stainless steel kitchen countertop L-corner joined with Fadior's tight-seam hairline method

Real Tight-Seam Corner Joint

Close-up of Fadior's tight-seam stainless countertop joint: the fold radius is removed along the joint line and locked underneath with steel L-plates, leaving only a crisp straight hairline seam.

Macro photograph of a micro-embossed snow-crystal stainless steel countertop and rounded sink drain rim

Snow-Crystal Embossed Sink Corner

Macro detail of a micro-textured snow-crystal stainless surface engineered to scatter light and reduce visible daily cookware marks.

4-Step Stainless Countertop Installation Protocol

  1. 01Verify panel dimensions and surface finish; confirm all base cabinets sit completely level and plumb.
  2. 02Position the stainless countertop, aligning front overhangs cleanly with cabinet doors and rear wall lines.
  3. 03Lock underside steel L-plates using M6 × 10 machine screws and shim until every seam is flush.
  4. 04Wipe clean with a soft cloth and apply load checks across every joint and sink perimeter.

Horizontal Worktop Planning — One Gold Zone, Two Silver Zones

Balance sink, preparation, and cooktop ergonomics along every straight or L-shaped kitchen run.

Silver Zone · Prep & Drain≥ 300 mm

Sink to wall clearance for fresh ingredients and dish draining.

Gold Zone · Main Worktop≥ 600 mm

Primary chopping and prep surface between sink and cooktop.

Silver Zone · Plating≥ 300 mm

Cooktop to wall clearance for landing hot cookware and serving plates.

05 · Independent Lab Proof & Daily Countertop Care

Accredited GQI indoor-emission tests and practical stainless care.

Both our 304 stainless steel countertop and Q1803 (QN1803) stainless steel countertop passed independent indoor air emission testing at the Guangdong Testing Institute of Product Quality Supervision (GQI, CMA & CNAS L0153) with formaldehyde not detected.

Verified Countertop Emission Reports (GQI · January 2026)

Accredited GQI test report SQ2505791 cover page for Fadior 304 stainless steel kitchen countertop emission testing
SQ2505791 · GQI · CNAS L01532026-01-26

304 Stainless Steel Kitchen Countertop (Grade E_NF)

Formaldehyde not detected (< 0.005 mg/m³) · TVOC 0.01 mg/(m²·h)

Formaldehyde not detected (< 0.005 mg/m³ vs E_NF limit ≤ 0.025 mg/m³), toluene not detected, and TVOC 0.01 mg/(m²·h) (limit ≤ 0.50). Pass.

GB/T 39600-2021 · GB/T 35601-2024 · HJ 571-2010 · CMA 240020349096 · CNAS L0153 · ilac-MRA
Accredited GQI test report SQ2505792 cover page for Fadior Q1803 QN1803 stainless steel kitchen countertop emission testing
SQ2505792 · GQI · CNAS L01532026-01-26

Q1803 (QN1803) Stainless Steel Countertop (Grade E_NF)

Formaldehyde (< 0.005 mg/m³), toluene & TVOC all not detected

Formaldehyde (< 0.005 mg/m³), toluene (< 2 μg/m³), and TVOC (< 0.010 mg/(m²·h)) all below detection limits. Pass. Specimen explicitly verified as Q1803 (QN1803), separate from 304.

GB/T 39600-2021 · GB/T 35601-2024 · HJ 571-2010 · CMA 240020349096 · CNAS L0153 · ilac-MRA

Each report applies strictly to the submitted test specimen. View alloy composition (SJ2501763: 19.31% Cr / 8.02% Ni) and food-contact heavy-metal migration (SC2500663: < 0.002 mg/kg) on our Quality & Testing Hub.

Inspect All 12 Lab Reports (Including 304 Chemistry & Food-Contact Migration)

Official Cleaning & Daily Maintenance Rules

Recommended Daily Care

  1. 01Peel off protective film during installation

    Remove factory film completely once installation finishes so adhesive never bakes onto the brushed or snow-crystal finish.

  2. 02Clean with a soft microfiber cloth and mild neutral soap

    Wipe daily spills and cooking grease gently along the grain direction on brushed or directional rock-grain worktops.

  3. 03Rinse thoroughly with clean water and wipe dry

    Never allow detergent film, brine, or mineral water droplets to evaporate on stainless steel surfaces or welded sink corners.

  4. 04Use chopping boards and stay within rated cabinet loads

    Protect textured finishes from heavy cleaver impacts and keep under-counter base panels within their 50 kg rated capacity.

Avoid on Stainless Countertops & Sinks

  1. ✕ 01No chlorine bleach or strong acidic / alkaline cleaners

    Chlorides and harsh descalers attack the passive chromium-oxide layer and can pit stainless steel surfaces.

  2. ✕ 02No steel wool, wire brushes, or abrasive scouring pads

    Carbon-steel wool embeds rust particles and permanently mars brushed, titanium, and snow-crystal finishes.

  3. ✕ 03Do not leave standing vinegar, salt brine, or wet iron pans overnight

    Prolonged contact with acidic condiments or wet cast-iron cookware causes surface discoloration or tea-staining.

  4. ✕ 04Do not overload recessed sinks or stand on countertop overhangs

    Respect structural cabinet support spans and always shim L-joints flush during installation.

06 · Buyer Specifications FAQ

Key questions about stainless steel countertops, sinks, and faucets.

Clear engineering answers before you finalize countertop drawings, sink cutouts, and faucet hole drilling.

Why does a 1.5 mm stainless steel countertop measure 1.3 mm in practice?

Per Fadior's 2026 countertop thickness specification and Chinese sheet standards GB/T 4237-2015 and GB/T 709-2019, stainless countertops are specified by nominal sheet thickness while finished panels fall within standard negative rolling, grinding, embossing, and levelling tolerances: 1.5 mm nominal measures 1.3 mm (±0.1 mm), 1.2 mm titanium steel measures 1.05 mm (±0.1 mm), and 1.0 mm QN1803 measures 0.9 mm (±0.1 mm) when checked with a micrometer at least 100 mm from the edge.

What is the difference between 304 stainless steel and Q1803 (QN1803) countertops?

304 stainless steel countertops are offered in 1.5 mm nominal brushed, snow-crystal, rock-grain, etched-lustre, and cloud-fleck sheets, 1.2 mm titanium finish, and 5–10 mm solid plates. Q1803 uses grade QN1803 sheet (1.0 mm nominal / 0.9 mm actual) laminated over a 0.4 mm honeycomb, PVC crust core, and steel square tube. Fadior never labels QN1803 as 304; both options passed GQI Grade E_NF emission tests with formaldehyde not detected (< 0.005 mg/m³).

Can the kitchen sink be welded seamlessly into a stainless steel countertop?

Yes. Selected 304 stainless steel sinks can be factory-welded directly into a 304 stainless steel countertop, eliminating raised silicone lips around the bowl. Every welded sink is inspected to ensure zero burn-through, zero solder spatter in the bowl, no blackened edges, and a smooth burr-free rim. Certain extra-large bowls require a countertop depth of at least 600 mm.

Are L-shaped or U-shaped stainless steel countertops completely seamless at corners?

Long L-shaped and U-shaped runs are joined with Fadior's tight-seam method: the sheet fold radius is removed along the meeting line and both sections are bolted tightly from underneath with steel L-plates and M6 × 10 machine screws. This creates a flat, tightly closed joint where a fine straight hairline seam remains cleanly visible.

Are all 36 kitchen and basin faucets made of 304 stainless steel?

No. Faucets are sourced partner fittings whose body materials vary by model — including chrome-plated brass/copper, matte-black brass/copper, brushed 304 stainless steel (such as FAG08002), stainless steel, and zinc alloy on specific utility basin models (such as FAG08054). Fadior confirms the exact faucet body material and lead time on every project quotation.

Can I pair 20 mm quartz or 12 mm sintered stone countertops with stainless steel cabinets?

Yes. Fadior's 304 stainless steel kitchen cabinet bodies support stainless steel, 20 mm quartz (12 active edge profiles including straight, bevel, water-stop, bullnose, and Roman ogee), and 12 mm sintered stone countertops (5 active edge profiles from slim 12 mm island edges to 50 mm mitred aprons). Physical material samples govern final colour and veining sign-off.

Project Specification & Samples

Request countertop edge drawings, physical swatches, and sink-faucet matching for your kitchen plan.